| Acquisition Scope Channels |
| Sample rate |
MSO/DSO701xB: 2 GSa/s each channel
MSO/DSO703xB: 2 GSa/sec each channel
MSO/DSO705xB, 710xB: 4 GSa/sec half channel*, 2 GSa/sec each channel
Equivalent-time sample rate: 400 GSa/s (when real-time mode is turned off) |
| Memory depth Standard |
2 channels/4 channels
8 Mpts/4 Mpts |
| Vertical resolution |
8 bits |
| Peak detection |
MSO/DSO701xB: 500-ps peak detect
MSO/DSO703xB: 500-ps peak detect
MSO/DSO705xB/710xB: 250-ps peak detect |
| Averaging |
Selectable from 2, 4, 8, 16, 32, 64 … to 65536 |
| High resolution mode |
up to 12 bits of resolution when ≥10 μs/div at 4 GSa/s or ≥20-μs/div at 2 GSa/s |
| Filter |
Sin (x)/x interpolation (single shot BW = sample rate/4 or bandwidth of scope, whichever is less) with vectors on and in real-time mode |
| Acquisition Digital Channels (7000B Series MSO or MSO-upgraded 7000B Series DSO) |
| Sample rate |
2 GSa/sec one pod**, 1 GSa/sec each pod |
| Maximum input frequency |
250 MHz |
| Memory depth Standard |
One pod/both pods (with scope channels turned off) 8 Mpts/4 Mpts
One pod/both pods (with scope channels turned on) 2.5 Mpts/ 1.25 Mpts |
| Vertical resolution |
1 bit |
| Glitch detection |
2 ns (min pulse width) |
| Vertical system Scope Channels |
| Scope channels |
MSO/DSO7xx2B: Ch 1 and 2 simultaneous acquisition
MSO/DSO7xx4B: Ch 1, 2, 3 and 4 simultaneous acquisition |
| Bandwidth (–3 dB)* |
MSO/DSO701xB: DC to 100 MHz
MSO/DSO703xB: DC to 350 MHz
MSO/DSO705xB: DC to 500 MHz
MSO/DSO710xB: DC to 1 GHz |
| AC coupled |
MSO/DSO701xB: 3.5 Hz to 100 MHz
MSO/DSO703xB: 3.5 Hz to 350 MHz
MSO/DSO705xB: 3.5 Hz to 500 MHz
MSO/DSO710xB: 3.5 Hz to 1 GHz |
| Calculated rise time (=0.35/bandwidth) |
MSO/DSO701xB: 3.5 nsec
MSO/DSO703xB: 1 nsec
MSO/DSO705xB: 700 psec
MSO/DSO710xB: 350 psec |
| Single-shot bandwidth |
MSO/DSO701xB: 100 MHz
MSO/DSO703xB: 350 MHz
MSO/DSO705xB: 500 MHz
MSO/DSO710xB: 1 GHz (in half-channel mode) |
| Range |
MSO/DSO701xB, MSO/DSO703xB and MSO/DSO705xB: 2 mV/div to 5 V/div (1 MΩ or 50 Ω) MSO/DSO710xB: 2 mV/div to 5 V/div (1 MΩ), 2 mV/div to 1 V/div (50 Ω) |
| Maximum input |
CAT I 300 Vrms, 400 Vpk; transient overvoltage 1.6 kVpk
CAT II 100 Vrms, 400 Vpk
With 10073C/D 10:1 probe: CAT I 500 Vpk, CAT II 400 Vpk |
| Offset range |
±5 V on ranges <10 mV/div; ±20 V on ranges 10 mV/div to 200 mV/div;
±75 V on ranges >200 mV/div |
| Dynamic range |
±8 div |
| Input impedance |
1 MΩ ± 1% || 14 pF or 50 Ω ± 1.5%, selectable |
| Coupling |
AC, DC |
| BW limit |
25 MHz selectable |
| Channel-to-channel isolation |
DC to max bandwidth >40 dB |
| Standard probes |
10073D or 10074D shipped standard for each scope channel (N2873A or N2871A optional) |
| Probe ID |
Auto probe sense and AutoProbe interface
Agilent- and Tektronix-compatible passive probe sense |
| Vertical System Scope Channels |
| ESD tolerance |
±2 kV |
| Noise, RMS, input shorted |
MSO/DSO701xB: 0.50% FS or 300 μV, whichever is greater
MSO/DSO703xB: 0.50% FS or 300 μV, whichever is greater
MSO/DSO705xB: 0.50% FS or 360 μV, whichever is greater
MSO/DSO710xB: 0.65% FS or 360 μV, whichever is greater |
| DC vertical gain accuracy |
±2.0% full scale |
| DC vertical offset accuracy |
≤200 mV/div: ±0.1 div ±2.0 mV ±0.5% offset value;
>200 mV/div: ±0.1 div ±2.0 mV ±1.5% offset value |
| Single cursor accuracy |
±{DC vertical gain accuracy + DC vertical offset accuracy + 0.2% full scale (~1/2 LSB)} Example: for 50 mV signal, scope set to 10 mV/div (80 mV full scale), 5 mV offset, accuracy = ±{2.0% (80 mV) + 0.1 (10 mV) + 2.0 mV + 0.5% (5 mV) + 0.2% (80 mV)} ± 4.785 mV |
| Dual cursor accuracy |
±{DC vertical gain accuracy + 0.4% full scale (~1 LSB)} Example: for 50 mV signal, scope set to 10 mV/div (80 mV full scale), 5 mV offset, accuracy = ±{2.0% (80 mV) + 0.4% (80 mV)} = ±1.92 mV |
| Vertical System Digital Channels (MSO or MSO-upgraded DSO) |
| Number of channels |
16 logic timing channels – labeled D15 - D0 |
| Threshold groupings |
Pod 1: D7 - D0
Pod 2: D15 - D8 |
| Threshold selections |
TTL, CMOS, ECL and user-definable (selectable by pod) |
| User-defined threshold range |
±8.0 V in 10 mV increments |
| Maximum input voltage |
±40 V peak CAT I; transient overvoltage 800 Vpk |
| Threshold accuracy* |
±(100 mV + 3% of threshold setting) |
| Input dynamic range |
±10 V about threshold |
| Minimum input voltage swing |
500 mV peak-to-peak |
| Input capacitance |
~8 pF with flying leads |
| Input resistance |
100 kΩ ±2% at probe tip |
| Channel-to-channel skew |
2 ns typical, 3 ns maximum |
| Horizontal |
| Range |
MSO/DSO701xB: 2 nsec/div to 50 sec/div
MSO/DSO703xB: 2 nsec/div to 50 sec/div
MSO/DSO705xB: 1 nsec/div to 50 sec/div
MSO/DSO710xB: 500 psec/div to 50 sec/div |
| Resolution |
2.5 ps |
| Time scale accuracy* |
≤ ± (15+2* (instrument age in years)) ppm |
| Vernier |
1-2-5 increments when off, ~25 minor increments between major settings when on |
| Delay range |
Pre-trigger (negative delay): Greater of 1 screen width or 1 ms
Post-trigger (positive delay): 1 s to 500 seconds |
| Analog delta-t accuracy |
Same channel: ±0.0015% reading ±0.1% screen width ±20 ps Channel-to-channel: ±0.0015% reading ±0.1% screen width ±40 ps Same channel example (MSO/DSO705xB): For signal with pulse width of 10 μs, scope set to 5 μs/div (50 μs screen width), delta-t accuracy = ±{0.0015% (10 μs) + 0.1% (50 μs) + 20 ps} = 50.17 ns |
| Logic delta-t accuracy |
Same channel: ±0.005% reading ±0.1% screen width ±(1 logic sample period, 1 ns) Channel-to-channel: ±0.005% reading ±0.1% screen width ±(1 logic sample period) ±chan-to-chan skew Same channel example: For signal with pulse width of 10 μs, scope set to 5 μs/div (50 μs screen width), delta-t accuracy = ±{0.005% (10 μs) + 0.1% (50 μs) + 1 ns} = 51.5 ns |
| Modes |
Main, zoom, roll, XY, segmented (optional) |
| XY |
Bandwidth: Max bandwidth Phase error at 1 MHz: < 0.5 degrees Z Blanking: 1.4 V blanks trace (use external trigger on MSO/DSO7xx2B, channel 4 on MSO/DSO7xx4B) |
| Reference positions |
Left, center, right |
| Segmented memory re-arm time |
8 μs (minimum time between trigger events) |
| Trigger system |
| Sources |
MSO7xx2B: Ch 1, 2, line, ext, D15 - D0
DSO7xx2B: Ch 1, 2, line, ext
MSO7xx4B: Ch 1, 2, 3, 4, line, ext, D15 - D0
DSO7xx4B: Ch 1, 2, 3, 4, line, ext |
| Modes |
Auto, normal (triggered), single |
| Holdoff time |
~60 ns to 10 seconds |
| Trigger jitter |
15 ps rms |
| Selections |
Edge, pulse width, pattern, TV, duration, sequence, CAN, LIN, USB, I2C, SPI, Nth edge burst, RS-232 with Option 232 |
| Edge |
Trigger on a rising, falling, alternating or either edge of any source |
| Pattern |
Trigger at the beginning of a pattern of high, low, and don’t care levels and/or a rising or falling edge established across any of the analog and digital channels, but only after a pattern has stabilized for a minimum of 2 nsec. The scope channel’s high or low level is defined by that channel’s trigger level. The logic channel’s trigger level is defined by the threshold for the pod, 0 - 7 or 8 - 15. |
| Pulse width |
Trigger when a positive- or negative-going pulse is less than, greater than, or within a specified range on any of the source channels.
Minimum pulse width setting: 5 ns (MSO/DSO701xB/703xB scope channels)
2 ns (MSO/DSO705xB/710xB scope channels)
2 ns (logic channels on 7000B Series MSO or
MSO-upgraded 7000B Series DSO)
Maximum pulse width setting: 10 s |
| TV |
Trigger using any scope channel on most analog progressive and interlaced video standards including HDTV/EDTV, NTSC, PAL, PAL-M or SECAM broadcast standards. Select either positive or negative sync pulse polarity. Modes supported include Field 1, Field 2, all fields, all lines, or any line within a field. TV trigger sensitivity: 0.5 division of sync signal. Trigger holdoff time can be adjusted in half field increments. |
| Sequence |
Arm on event A, trigger on event B (edge or pattern), with option to reset on event C or time delay. |
| CAN |
Trigger on CAN (controller area network) version 2.0A and 2.0B signals. Trigger on the start of frame (SOF) bit (standard). N5424A option supports triggering on remote frame ID (RTR), data frame ID (~RTR), remote or data frame ID, data frame ID and data, error frame, all errors, acknowledge error and overload frame. |
| FlexRay |
Trigger on FlexRay Frames, errors, events and cycle-multiplexed triggering. N5432C or option FLX supports also triggering on particular frame types symbolically, such as Startup frames, Null frame, Sync frame, etc., as well as Boolean NOT frame types. |
| LIN |
Trigger on LIN (local interconnect network) sync break at beginning of message frame (standard). N5424A option supports triggering on frame ID. |
| USB |
USB Trigger on USB (universal serial bus) start of packet, end of packet, reset complete, enter suspend, or exit suspend on the differential USB data lines. USB low speed and full speed are supported. |
| I2C |
Trigger on I2C (inter-IC bus) serial protocol at a start/stop condition or user defined frame with address and/or data values. Also trigger on missing acknowledge, address with no acq, restart, EEPROM read, and 10-bit write. |
| SPI |
Trigger on SPI (serial protocol interface) data pattern during a specific framing period. Supports positive and negative Chip Select framing as well as clock idle framing and user-specified number of bits per frame. |
| I2S |
This application provides triggering on audio bus protocol channels for audio left, right, either as well as =, ≠, >,< entered data values and within and out of range values. It provides the ability to easily view the audio packets on the waveform and in a listing window. |
| RS-232/UART |
This application eliminates the need to manually decode bus traffic. Using data captured on the scope or digital channels, the application provides the ability to easily view the information sent over a RS-232 serial bus. Display real-time time-aligned decode of transmit and receive lines. The application also enables triggering on RS-232/UART conditions. |
| Duration |
Trigger on a multi-channel pattern whose time duration is less than a value, greater than a value, greater than a time value with a timeout, or inside or outside of a set of time values.
Minimum duration setting: 2 ns
Maximum duration setting: 10 s |
| MIL-STD 1553 |
Trigger on specific Command/Status Words, Data Words, and error conditions. |
| Nth edge burst |
Trigger on the Nth edge of a burst that occurs after an idle time that you specify. Max edge count: 65,536. |
| Autoscale |
Finds and displays all active scope and logic (for 7000B Series MSO) channels, sets edge trigger mode on highest-numbered channel, sets vertical sensitivity on scope channels and thresholds on logic channels, time base to display ~1.8 periods. Requires minimum voltage >10 mVpp, 0.5% duty cycle and minimum frequency >50 Hz. |
| Scope channel triggering |
| Range (internal) |
±6 div from center screen |
| Sensitivity* |
<10 mV/div: greater of 1 div or 5 mV; ≥10 mV/div: 0.6 div |
| Coupling |
AC, ~10 Hz on MSO/DSO701xB/703xB/705xB/710xB, DC, noise reject, HF reject and LF reject (~50 kHz) |
| Digital (D15 - D0) channel triggering (7000B Series MSO or MSO-upgraded 7000B Series DSO) |
| Threshold range |
(user defined) ±8.0 V in 10 mV increments |
| Threshold accuracy |
±(100 mV + 3% of threshold setting) |
| Predefined thresholds |
TTL = 1.4 V, CMOS = 2.5 V, ECL = –1.3 V |
| Display system |
| Display |
12.1-inch (255 mm x 184 mm) diagonal color TFT LCD |
| Throughput of scope channels |
Up to 100,000 waveforms/sec in real-time mode |
| Resolution |
XGA – 768 vertical by 1024 horizontal points (screen area); 640 vertical by 1000 horizontal points (waveform area) 256 levels of intensity scale |
| Controls |
Waveform intensity on front panel. Vectors on/off; infinite persistence on/off, 8 x 10 grid with intensity control |
| Built-in help system |
Key-specific help displayed by pressing and holding key or softkey of interest. Language support for 11 languages including English, German, French, Russian, Japanese, Traditional Chinese, Simplified Chinese, Korean, Spanish, Portuguese and Italian. |
| Real-time clock |
Time and date (user adjustable) |
| Measurement features |
| Automatic measurements |
Measurements are continuously updated. Cursors track last selected measurement. Up to four measurements can be displayed on screen at any one time. |
| Voltage (scope channels only) |
Peak-to-peak, maximum, minimum, average, amplitude, top, base, overshoot, preshoot, RMS, standard deviation (AC RMS), Ratio (dB) |
| Time |
Frequency, period, + width, – width and duty cycle on any channel. Rise time, fall time, X at max Y (time at max volts), X at min Y (time at min volts), delay, and phase on scope channels only. |
| Counter |
Built-in 5-digit frequency counter on any channel. Counts up to the scope’s bandwidth (1 GHz max). The counter resolution can be increased to 8 digits with an external 10-MHz reference. |
| Threshold definition |
Variable by percent and absolute value; 10%, 50%, 90% default for time measurements |
| Cursors |
Manually or automatically placed readout of horizontal (X, ΔX, 1/ΔX) and vertical (Y, ΔY). Tracking Cursors provides an additional mode for cursor positioning beyond the current manual method. When cursor tracking is enabled, changing a cursor’s x-axis position results in the yaxis cursor tracking the corresponding y-axis (voltage, current, etc.) value. Additionally logic or scope channels can be displayed as binary or hex values. |
| Waveform math |
f (g(t))
g(t): { 1, 2, 3, 4, 1-2, 1+2, 1x2, 3-4, 3+4, 3x4}
f(t): { 1-2, 1+2, 1x2, 3-4, 3+4, 3x4, FFT(g(t)), differentiate d/dt
g(t),
integrate ∫ g(t) dt, square
root √g(t) }
Where 1,2,3,4 represent analog input channels 1, 2, 3, and 4
Note: Channels 3 and 4 only available on MSO/DSO7xx4B models |
| Measurement statistics |
Statistical data for enabled measurements such as mean, min, max, standard deviation and count |
| Precision Mode |
Automatic measurements, waveform math and FFT performed on up to 128Kpts data record |
| FFT |
| Points |
Up to 128 Kpts in precision mode |
| Source of FFT |
1, 2, 1+2, 1-2, 1x2, MSO/DSO7xx4A: 3, 4, 3+4, 3-4, 3x4; |
| where 1, 2, 3, 4 represent the analog channel inputs 1, 2, 3, and 4 |
| Window |
Rectangular, flattop, Hanning, Blackman Harris |
| Noise floor |
–50 to –90 dB depending on averaging |
| Amplitude |
Display in dBV, dBm at 50 Ω |
| Frequency resolution |
0.05/time per div |
| Maximum frequency |
50/time per div |
| Storage |
| Save/recall (non-volatile) |
10 setups and traces can be saved and recalled internally. Optional secure environment mode ensures setups and traces are stored to internal volatile memory so data is erased when power is removed. Compliant to NISPOM Chapter 8 requirements. |
| Storage type and format |
USB 1.1 host ports on front and rear panels
Image formats: BMP (8-bit), BMP (24-bit), PNG (24-bit)
Data formats: X and Y (time/voltage) values in CSV format, ASCII XY and binary format and .alb for offline viewing on a PC
Trace/setup formats: Recalled |
| I/O |
| Standard ports |
USB 2.0 high-speed device, two USB 1.1 host ports, 10/100BaseT LAN, XGA video output |
| Max transfer rate |
USB (USBTMC-USB488): 3.5 Mbytes/sec
100 Mbps LAN (TCP/IP): 1 Mbytes/sec |
| Supported printers via USB |
For a list of currently supported printers visit www.agilent.com/fi nd/Infi niiVision-printers |
| General characteristics |
| Physical size (WxHxD) |
17.9” x 11.7” x 8.6” (45.4 cm x 29.8 cm x 22 cm) with legs extended, with screen cover on
17.9” x 10.9” x 6.8” (45.4 cm x 27.7 cm x 17.3 cm) with legs contracted, with screen cover on |
| Weight |
Net: 5.9 kg (13 lbs) Shipping: 9.3 kg (20.5 lbs) |
| Probe comp output |
Frequency ~1.2 kHz; Amplitude ~2.5 V |
| General characteristics |
| Trigger out |
When Triggers is selected (delay ~17 ns)
0 to 5 V into high impedance
0 to 2.5 V into 50 Ω
When Source Frequency or Source Frequency/8 is selected
0 to 580 mV into high impedance
0 to 290 mV into 50 Ω
Max frequency output: 350 MHz (in source frequency mode when terminated in 50 Ω)
125 MHz (in source frequency/8 mode when terminated in 50 Ω) |
| 10 MHz ref in/out |
TTL out, 180 mV to 1 V amplitude with 0 to 2 V offset |
| Kensington lock |
Connection on rear panel for security |
| Power requirements |
| Line voltage range |
100-120V, 50/60/400 Hz; 100-240V, 50/60 Hz auto ranging |
| Line frequency |
50/60 Hz, 100-240 VAC; 400 Hz, 100-120 VAC |
| Power usage |
120 W max |
| Environmental characteristics |
| Ambient temperature |
Operating -10 °C to +55 °C; non-operating –40 °C to +70 °C |
| Humidity |
Operating: Up to 95% relative humidity (non-condensing) at +40 °C
Non-operating: Up to 90% relative humidity at +65 °C |
| Altitude |
Operating to 4,570 m (15,000 ft); non-operating to 15,244 m (50,000 ft) |
| Vibration |
Agilent class B1 and MIL-PRF-28800F; class 3 random |
| Shock |
Agilent class B1 and MIL-PRF-28800F; class 3 random; (operating 30g, 1/2 sine, 11 ms duration, 3 shocks/axis along major axis, total of 18 shocks) |
| Pollution degree |
Normally only dry non-conductive pollution occurs.
Occasionally a temporary conductivity caused by condensation must be expected. |
| Typical operator noise |
30 dBa at front of instrument, 35 dBa at rear of instrument. |
| Indoor use |
Rated for indoor use only |
| Other |
| Measurement categories |
CAT I |
| Regulatory information |
Safety IEC 61010-1:2001 / EN 61010-1:2001
Canada: CSA C22.2 No. 1010.1:1992
UL 61010B-1:2003 |
| Supplementary information |
The product herewith complies with the requirements of the Low Voltage Directive
73/23/EEC and the EMC Directive 89/336/EEC, and carries the CE-marking accordingly.
The product was tested in a typical configuration with HP/Agilent test systems. |
| Accessories included |
Standard 3-year warranty
Standard probe
100 MHz : 10074D (default), N2871A (optional – as option 002)
350 MHz – 1GHz : 10073D (default), N2873A (optional – as option 002)
16 channel flying lead set logic probe (two pods with eight channels each)
54695-62301 Probe accessory pouch
Built-in help language support for English, French, German, Russian, simplified Chinese, traditional Chinese, Korean, Spanish, Portuguese, Japanese and Italian
Interface language support GUI menus: English, simplified Chinese, traditional Chinese, Korean, Japanese Key/knob overlay: English, simplified Chinese, traditional Chinese, Japanese
Printed user’s guide (option ABA for English, option AB2 for simplified Chinese, option ABJ for Japanese)
Documentation CD (PDFs of Programmer’s Reference Guide, User Guide, and Service Guide)
Agilent I/O libraries suite 15.0
Localized power cord
Front panel cover |