Sample |
Sample Mode |
Real-time sample |
Max. Real-time Sample Rate |
2.0 GSa/s for each channel |
Max. Memory Depth |
14 Mpts for each channel |
Peak Detect |
500 ps |
Averaging |
After all the channels finish N times of sampling at the same time, N can be 2, 4, 8, 16, 32, 64,
128, 256, 512, 1024, 2048, 4096, or 8192. |
High Resolution |
12 bits when =10 µs/div @ 2 GSa/s. |
Input |
Number of Channels |
4 analog channels |
Input Coupling |
DC, AC, or GND |
Input Impedance |
(1 MΩ±1%) || (15 pF±3 pF) or 50 Ω±1.5% |
Probe Attenuation Coefficient |
0.01X to 1000X, in 1-2-5 step |
Maximum Input Voltage (1 MΩ) |
CAT I 300 Vrms, CAT II 100 Vrms, transient overvoltage 1000 Vpk
with RP2200 10:1 probe: CAT II 300 Vrms
with RP3300A 10:1 probe: CAT II 300 Vrms
with RP3500A 10:1 probe: CAT II 300 Vrms
with RP5600A 10:1 probe: CAT II 300 Vrms |
Horizontal |
Time Base Scale |
DS4024E: 2 ns/div to 1 ks/div
DS4014E: 5 ns/div to 1 ks/div |
Deviation between Channels |
1 ns (typical), 2 ns (maximum) |
Max. Recording Length |
14 Mpts for each channel |
Time Base Accura cy[1] |
= ±4 ppm |
Clock Drift |
= ±2 ppm/year |
Delay Range |
Pre-trigger (negative delay): Memory Depth/Sample Rate
Post-trigger (positive delay): 1 s to 100 ks |
Time Base Mode |
Y-T, X-Y, Roll, Delayed |
Number of X-Ys |
2 paths at the same time |
Waveform Capture Rate [2] |
60,000 wfms/s |
Zero Offset |
±0.5 div*minimum time base scale |
Vertical |
Bandwidth (-3 dB) (50 Ω) |
DS4024E: DC to 200 MHz
DS4014E: DC to 100 MHz |
Single Bandwidth (50 Ω) |
DS4024E: DC to 200 MHz
DS4014E: DC to 100 MHz |
Vertical Resolution |
8 bits |
Vertical Scale |
1 MΩ input impedance: 1 mV/div to 5 V/div
50 Ω input impedance: 1 mV/div to 1 V/div |
Offset Range |
1 MΩ input impedance:
1 mV/div to 225 mV/div: ±2 V
230 mV/div to 5 V/div: ±40 V
50 Ω input impedance:
1 mV/div to 124 mV/div: ±1.2 V
126 mV/div to 1 V/div: ±12 V |
Dynamic Range |
±5 div |
Bandwidth Limit [1] |
DS4024E: 20 MHz/100 MHz
DS4014E: 20 MHz |
Low Frequency Response
(AC coupling, -3 dB) |
=5 Hz (on BNC) |
Calculated Rise Time [1] |
DS4024E: 1.8 ns
DS4014E: 3.5 ns |
DC Gain Accuracy |
±2% full scale |
DC Offset Accuracy |
200 mV/div to 5 V/div: ±0.1 div ± 2 mV ± 0.5% offset
1 mV/div to 195 mV/div: ±0.1 div ± 2 mV ± 1.5% offset |
ESD Tolerance |
±2 kV |
Channel-to-Channel Isolation |
DC to maximum bandwidth: >40 dB |
Trigger |
Trigger Level Range |
Internal: ±6 div from the center of the screen
EXT: ±0.8 V |
Trigger Mode |
Auto, Normal, Single |
Holdoff Range |
100 ns to 10 s |
High Frequency Rejection [1] |
50 kHz |
Low Frequency Rejection [1] |
5 kHz |
Edge Trigger |
Edge Type |
Rising, Falling, Rising&Falling |
Pulse Trigger |
Pulse Condition |
Positive Pulse Width (greater than, lower than, within the specific interval);
Negative Pulse Width (greater than, lower than, within the specific interval) |
Pulse Width Range |
4 ns to 4 s |
Runt Trigger |
Pulse Polarity |
Positive, Negative |
Qualifier |
None, >, <, <> |
Pulse Width Range |
4 ns to 4 s |
Nth Edge Trigger |
Edge Type |
Rising, Falling |
Idle Time |
40 ns to 1 s |
Number of Edges |
1 to 65535 |
Slope Trigger |
Slope Condition |
Positive Slope (greater than, lower than, within the specific interval);
Negative Slope (greater than, lower than, within the specific interval) |
Time Setting |
10 ns to 1 s |
Video Trigger |
Polarity |
Positive, Negative |
Synchrony |
All Lines, Line Num, Odd Field, Even Field |
Standard |
NTSC, PAL/ECAM, 480P, 576P, 720P, 1080P, and 1080I |
Pattern Trigger |
Pattern Setting |
H, L, X, Rising Edge, Falling Edge |
RS232/UART Trigger |
Polarity |
Normal, Invert |
Trigger Condition |
Start, Error, Check Error, Data |
Baud Rate |
2400 bps, 4800 bps, 9600 bps, 19200 bps, 38400 bps, 57600 bps, 115200 bps, 230400 bps,
460800 bps, 921600 bps, 1Mbps, User |
Data Bits |
5 bit, 6 bit, 7 bit, 8 bit |
I2C Trigger |
Trigger Condition |
Start, Restart, Stop, Missing ACK, Address, Data, A&D |
Address Bits |
7 bits, 8 bits, 10 bits |
Address Range |
0 to 127, o to 255, 0 to 1023 |
Byte Length |
1 to 5 |
SPI Trigger |
Trigger Condition |
CS, Timeout |
Timeout Value |
100 ns to 1 s |
Data Bits |
4 bit to 32 bit |
Data |
H, L, X |
Clock |
Edge Rising Edge, Falling Edge |
CAN Trigger |
Signal Type |
Rx, Tx, CAN_H, CAN_L, Differential |
Trigger Condition |
SOF, EOF, Frame Type, Frame Error |
Baud Rate |
10 kb/s, 20 kb/s, 33.3 kb/s, 50 kb/s, 62.5 kb/s, 83.3 kb/s, 100 kb/s, 125 kb/s, 250 kb/s, 500 kb/s,
800 kb/s, 1 Mb/s, User |
Sample Point |
5% to 95% |
Frame Type |
Data, Remote, Error, OverLoad |
Error Type |
Bit Fill, Answer Error, Check Error, Format Error, Random Error |
FlexRay Trigger |
Baud Rate |
2.5 Mb/s, 5 Mb/s, 10 Mb/s |
Trigger Condition |
Frame, Symbol, Error, TSS |
USB Trigger |
Signal Speed |
Low Speed, Full Speed |
Trigger condition |
SOP, EOP, RC, Suspend, Exit Suspend |
LIN Trigger |
Version |
1.X, 2.X, Both |
Trigger Condition |
Sync, Identifier, Data, ID&Data, Wakeup, Sleep, Error |
ID Range |
0 to 63 |
Data Comparison |
=, ?, <, >, =, = |
Data Length |
1 to 8 |
Data Level |
H, L |
Baud Rate |
"19200 bps, 10417 bps, 9600 bps, 4800 bps, 2400 bps, 1200 bps, User |
Error Type |
Sync, Even-Odd, Checksum |
Measure |
Number of Measurements |
Displays 5 measurements at the same time. |
Measurement Range |
Screen Region, Cursor Region |
Statistic Mode |
Extremum, Difference |
Measurement Statistic |
Average, Max, Min, Standard Deviation, Number of Measurements |
FontSize |
Normal, Large, UltraLarge |
DisItem |
ON, OFF |
Frequency Counter |
6-digit hardware frequency counters |
Math Operation |
Waveform Operation |
A+B, A-B, A×B, A÷B, FFT, Digital Filter, Editable Advanced Operation, Logic Operation |
FFT Window |
Rectangle, Hanning, Blackman, Hamming |
FFT Display |
Split, Full Screen |
FFT Vertical Scale |
Vrms, dB |
Logic Operatio |
n AND, OR, NOT, XOR |
Math Function |
Intg, Diff, Lg, Ln, Exp, Abs, Square, Sqrt, Sine, Cosine, Tangent |
Decoding |
Number of Buses |
2 |
Decoding Type |
Parallel (standard), RS232/UART (optional), I2C (optional), SPI (optional), CAN (optional), FlexRay
(optional), LIN (optional) |
Parallel |
Combines the sample data of the source channel waveforms as a parallel multi-channel bus and
displays the data as a single bus value |
RS232/UART |
Displays the input signal(s) of the TX source channel or/and RX source channel as bus |
I2C |
Displays the input signal of the SDA source channel as bus |
SPI |
Displays the input signal(s) of the MISO source channel or/and MOSI source channel as bus |
CAN |
Displays the input signal of the source channel (Rx, Tx, CAN_H, CAN_L, or differential) as bus |
FlexRay |
Displays the input signal of the source channel (BP, BM, or RX/TX) as bus |
LIN |
Displays the input signal of the source channel of LIN as bus |
Display |
Display Type |
9-inch (229 mm) TFT LCD display |
Display Resolution |
800 horizontal×RGB×480 vertical pixel |
Display Color |
160,000 colors |
Persistence Time |
Min, 50 ms, 100 ms, 200 ms, 500 ms, 1 s, 2 s, 5 s, 10 s, 20 s, Infinite |
Display Type |
Dots, Vectors |
Real-time Clock |
Time and Date (adjustable for users) |
I/O |
Standard Ports |
Dual USB HOST, USB DEVICE, LAN, VGA Output, 10 MHz Input/Output, Aux Output (TrigOut,
Fast, PassFail, GND) |
Printer Compatibility |
PictBridge |
General Specifications |
Probe Compensation Output |
Output Voltage [1] |
About 3 V, peak-peak |
Frequency [1] |
1 kHz |
Power |
Power Voltage |
100 to 127 V, 45 to 440Hz
100 to 240 V, 45 to 65Hz |
Power |
Maximum 120 W |
Fuse |
3 A, T degree, 250 V |
Environment |
Temperature Range |
Operating: 0°C to +50°C
Non-operating: -40°C to +70°C |
Cooling Method Fan |
cooled |
Humidity Range |
0°C to +30°C: =95% RH
+30°C to +40°C: =75% RH
+40°C to +50°C: =45% RH |
Altitude |
Operating: under 3,000 meters
Non-operating: under 15,000 meters |
Physical Characteristics |
Size [3] |
Width×Height×Depth = 440.0 mm×218.0 mm×130.0 mm |
Weight [4] |
Packaging Excluded 4.8 kg±0.2 kg
Packaging Included 7.1 kg±1.0 kg |
Adjustment Interval |
The recommended calibration interval is one year. |
EMC |
2014/35/EU
Execution standard EN 61326-1:2013 |
Safety |
EN 61010-1:2010
EN 61010-2-030:2010
IEC 61010-1:2010 (Third Edition)
CAN/CSA C22.2 No.61010-1-12
UL 61010-1:2012 |