| Frequency |
| Range |
9 kHz to 3.0 GHz |
| Resolution |
1 Hz |
| Accuracy |
±[(period since last adjustment X aging rate) + stability over
temperature + supply voltage stability |
| Aging Rate |
±2 ppm max. |
1 year after last adjustment |
Frequency Stability
over Temperature |
±0.025 ppm |
0 to 50 °C |
Supply Voltage
Stability |
±0.02 ppm |
Start, Stop, Center,
Marker |
±(marker frequency indication X frequency reference accuracy +
10% x RBW + frequency resolution1) |
| Sweep points |
601 |
Span >= 100 Hz |
| 6 to 601 |
Span = 0 Hz |
| Resolution |
1 Hz, 10 Hz, 100 Hz, 1 kHz |
| Accuracy |
±(marker frequency indication X
frequency reference accuracy +
counter resolution) |
RBW/Span >=0.02 ;
Mkr level to DNL>30 dB |
| Range |
0 Hz (zero span), 100 Hz to 3 GHz |
| Resolution |
1 Hz |
| Accuracy |
± frequency resolution1 |
| Accuracy |
|
Fc =1 GHz; RBW = 1 kHz, VBW
= 10 Hz;Average ≥ 40 |
| 10 kHz |
<-88 dBc/Hz |
Typical2 |
| 100 kHz |
<-95 dBc/Hz |
Typical |
| 1 MHz |
<-113 dBc/Hz |
Typical |
| Filter Bandwidth |
1 Hz to 1 MHz in 1-3-10 sequence |
-3dB bandwidth |
| 200 Hz, 9 kHz, 120 kHz, 1 MHz |
-6dB bandwidth |
| Accuracy |
± 8%, RBW = 1 MHz |
Nominal3 |
| ± 5%, RBW < 1 MHz |
Nominal |
| Shape Factor |
< 4.5:1 |
Normal Bandwidth ratio:
-60dB:-3dB |
| Filter Bandwidth |
1 Hz to 1 MHz in 1-3-10 sequence |
-3dB bandwidth |
[1] Frequency Resolution = Span/(Sweep points - 1)
[2] Typical specifications in this datasheet mean that the performance can be exhibited in 80% of the units with a 95% confidence level over the temperature range 20 to 30 °C. They are not
covered by the product warranty.
[3] Nominal values indicate expected performance. They are not covered by the product warranty. |
| Amplitude |
| Measurement |
100 kHz to 1 MHz |
Displayed Average Noise Level
(DANL) to 18 dBm |
| 1 MHz to 10 MHz |
DANL to 21 dBm |
| 10 MHz to 3 GHz |
DANL to 30 dBm |
Input Attenuator
Range |
0 to 50 dB, in 1 dB step |
Auto or manual setup |
Average Total
Power |
<= 33 dBm |
Input attenuator
≥10 dB |
| DC Voltage |
± 50 V |
|
Total Power at 1st
Mixer |
> 0 dBm |
Typical;Fc ≥50 MHz; preamp. off |
Total Power at the
Preamp |
> -22 dBm |
Typical;Fc ≥50 MHz; preamp. on |
| |
|
mixer power level (dBm)= input
power (dBm)-attenuation (dB) |
| Preamp off |
0 dB attenuation; RF Input is terminated with a 50 Ohm load. RBW
10 Hz; VBW 10 Hz; span 500 Hz; reference level = -60dBm; trace
average ≥ 40 |
| 9 kHz to 100 kHz |
< -93 dBm, |
| 100 kHz to 1 MHz |
< -90 dBm - 3 x (f/100 kHz) dB |
| 1 MHz to 10 MHz |
< -122 dBm Nominal |
| 10 MHz to 3 GHz |
< -122 dBm |
| Preamp on |
0 dB attenuation; RF Input is terminated with a 50 Ohm load. RBW
10 Hz; VBW 10Hz; span 500 Hz; reference level = -60dBm; trace
average ≥ 40 |
| 100 kHz to 1 MHz |
< -108 dBm - 3 x (f/100 kHz) dB |
| 1 MHz to 10 MHz |
< -142 dBm |
| 10 MHz to 3 GHz |
< -142 dBm + 3 x (f/1 GHz) dB |
| [4] DANL spec shall exclude the Spurious Response |
| Scales |
Log, Linear |
| Units |
dBm, dBmV, dBuV, V, W |
Marker Level
Readout |
0.01 dB |
Log scale |
| 0.01 % of reference level |
Linear scale |
Level Display
Modes |
Trace, Topographic, Spectrogram |
Single / split Windows |
| Number of Traces |
4 |
| Detector |
Positive-peak, negative-peak,
sample, normal, RMS(not Video) |
an be setup for each trace
separately |
| Trace Functions |
Clear & Write, Max/Min Hold, View,
Blank, Average |
| Absolute Point |
Center=160 MHz ; RBW 10 kHz; VBW 1 kHz; span 100 kHz; log
scale; 1 dB/div; peak detector; 20 to 30°C; signal 0 dBm |
| Preamp off |
± 0.3 dB |
Ref level 0 dBm; 10 dB
RF attenuation |
| Preamp on |
± 0.4 dB |
Ref level -30 dBm; 0 dB
RF attenuation |
| Preamp off |
Attenuation: 10 dB; Reference: 160 MHz; 20 to 30°C |
| 100 kHz to 2.0 GHz |
± 0.5 dB |
| 2.0GHz to 3.0 GHz |
± 0.7 dB |
| Preamp on |
Attenuation: 0 dB; Reference: 160 MHz; 20 to 30°C |
| 1 MHz to 2.0 GHz |
± 0.6 dB |
| 2.0GHz to 3.0 GHz |
± 0.8 dB |
| Attenuator setting |
0 to 50 dB in 1 dB step |
| Uncertainty |
± 0.15 dB |
reference: 160 MHz, 10dB
attenuation |
| 1 Hz to 1 MHz |
± 0.25 dB |
reference : 10 kHz RBW |
Overall Amplitude
Accuracy |
± 1.5 dB |
20 to 30°C; frequency > 1 MHz;
Signal input 0 to -50 dBm;
Reference level 0 to -50 dBm;
Input attenuation 10 dB;
RBW 1 kHz; VBW 1 kHz; after cal;
Preamp Off |
| ± 0.5 dB |
Typical |
Second Harmonic
Intercept |
|
Preamp off; signal input
-30dBm; 0 dB attenuation |
| +35 dBm |
Typical; 10 MHz < fc < 775 MHz |
| +60 dBm |
Typical; 775 MHz ≤ fc < 1.5 GHz |
Third-order
Intercept |
|
Preamp off; signal input
-30dBm; 0 dB attenuation |
| > 1dBm |
300 MHz to 3 GHz |
Input Related
Spurious |
< -60 dBc |
Input signal level -30 dBm, Att.
mode, Att=0 dB; 20-30 degree
C |
Residual Response
(inherent) |
<-90 dBm |
Input terminated; 0 dB
attenuation; Preamp off |
| Sweep |
| Range |
22 ms to 1000 s |
Span >= 100 Hz |
| 50 us to 1000 s |
Span = 0 Hz; Min Resolution =
10 us |
| Sweep Mode |
Continuous; Single |
| Trigger Source |
Free run; Video; External |
| Trigger Slope |
Positive or negative edge |
| RF Preamplifier |
| Frequency Range |
1 MHz to 3 GHz |
| Gain |
18 dB |
Nominal
(installed as standard) |
| Front Panel Input/Output |
| Connector Type |
N-type female |
| Impedance |
50 ohm, nominal |
| VSWR |
<1.6 :1 |
300 kHz to 3 GHz; Input
attenuator ≥ 10 dB |
| Connector Type |
SMB male |
| Voltage/Current |
DC +7V / 500 mA max |
With short-circuit protection |
| Connector Type |
A plug |
| Protocol |
Version 2.0 |
Supports Full/High/Low speed |
| Protocol |
SD 1.1 |
| Supported Cards |
MicroSD, MicroSDHC |
Up to 32GB capacity |
| Rear Panel Input/Output |
| Connector Type |
BNC female |
| Output Frequency |
10 MHz |
| Output Amplitude |
3.3V CMOS |
| Output Impedance |
50 ohm |
| Connector Type |
BNC female |
Input Reference
Frequency |
10 MHz |
| Input Amplitude |
-5 dBm to +10 dBm |
Frequency Lock
Range |
Within ± 5 ppm of the input
reference frequency |
| Connector Type |
BNC female; Open-collector |
| Connector Type |
BNC female |
| Input Amplitude |
3.3V CMOS |
| Switch |
Auto selection by function |
| Connector Type |
RJ-45 |
| Base |
10Base-T; 100Base-Tx; Auto-MDIX |
| Connector Type |
B plug |
For remote control only;
supports USB TMC |
| Protocol |
Version 2.0 |
Supports Full/High speed |
| Connector Type |
SMA female |
| Impedance |
50 ohm |
Nominal |
| IF Frequency |
886 MHz |
Nominal |
| Output level |
-25 dBm |
10 dB attenuation; RF input: 0
dBm @ 1 GHz; |
| Connector Type |
3.5mm stereo jack,
wired for mono operation |
| Connector Type |
DVI-I ( integrated analog and
digital) , Single Link |
Compatible with VGA or HDMI
standard through adapter |
| Connector Type |
D-sub 9-pin female |
Tx,Rx,RTS,CTS |
| Connector Type |
IEEE-488 bus connector |
| Power Source |
AC 100 V to 240 V, 50 / 60 Hz |
Auto range selection |
| Battery pack |
6 cells, Li-Ion rechargeable, 3S2P |
With UN38.3 Certification |
| Voltage |
DC 10.8 V |
| Capacity |
5200 mAh / 56Wh |
| General |
Internal Data
storage |
16 MB nominal |
| Power Consumption |
<65 W |
| Warm-up Time |
< 30 minutes |
| Temperature Range |
+5 °C to +45 °C |
Operating |
| -20 °C to + 70 °C |
Storage |
| Weight |
4.5 kg (9.9 lb) |
Inc. all options
(Basic+TG+GPIB+Battery) |
| Dimensions |
210 x 350 x 100 (mm)
8.3 x 13.8 x 3.9 (in) |
Approximately |
| Tracking Generator5 (Optional) |
| Frequency Range |
100 kHz to 3 GHz |
| Output Power |
-50 dBm to 0 dBm in 0.5 dB steps |
| Absolute Accuracy |
± 0.5 dB |
@160 MHz, -10 dBm, Source
attenuation 10 dB, 20 to 30°C |
| Output Flatness |
Referenced to 160 MHz, -10 dBm |
| 100 kHz to 2 GHz |
± 1.5 dB |
| 2 GHz to 3 GHz |
± 2.0 dB |
Output Level
Switching
Uncertainty |
± 0.8 dB |
Referenced to -10 dBm |
| Harmonics |
< -30 dBc |
Typical, output level = -10 dBm |
| Reverse Power |
+30 dBm max. |
| Connector type |
N-type female |
| Impedance |
50 ohm |
Nominal |
| Output VSWR |
< 1.6:1 |
300 kHz to 3 GHz, source
attenuation ≥ 12 dB |
| [5] The minimum RBW filter is 10 kHz when the TG output is ON. |
| USB Power Sensor (Optional) |
| Type |
Average power sensor |
Model: PWS-06 |
| Interface to Meter |
USB cable to GSP930 Front-Panel USB Host |
| Connector Type |
N-type male, 50 ohm nominal |
| Input VSWR |
1.1: 1 |
Typical |
| 1.3: 1 |
Max |
| Input Frequency |
1 to 6200 MHz |
| Sensing Level |
-32 to +20 dBm |
Max. Input Damage
Power |
<= 27 dBm |
Power
Measurement
Uncertainty
@ 25 °C |
-30 dBm to +5 dBm:
1 MHz to 3GHz: ±0.10 dB typical ±0.30 dB max.
3 GHz to 6 GHz: ±0.15 dB typical ±0.30 dB max.
+5 dBm to +12 dBm:
1 MHz to 3GHz: ±0.15 dB typical ±0.30 dB max.
3 GHz to 6 GHz: ±0.15 dB typical ±0.30 dB max.
+12 dBm to +20 dBm:
1 MHz to 3GHz: ±0.20 dB typical ±0.40 dB max.
3 GHz to 6 GHz: ±0.20 dB typical ±0.40 dB max. |
Power
Measurement
Uncertainty
@ 0 to 25 °C |
-30 dBm to +5 dBm:
1 MHz to 3GHz: ±0.25 dB typical
3 GHz to 6 GHz: ±0.25 dB typical
+5 dBm to +12 dBm:
1 MHz to 3GHz: ±0.20 dB typical
3 GHz to 6 GHz: ±0.20 dB typical
+12 dBm to +20 dBm:
1 MHz to 3GHz: ±0.35 dB typical
3 GHz to 6 GHz: ±0.30 dB typical |
| Linearity @ 25 °C |
±3 % |
| Measurement |
100 ms for Low Noise Mode |
Typical |
| Speed |
30 ms for Fast Mode |