Vertical Amplifiers (CH 1 and CH 2) |
Sensitivity |
5mV/div - 5V/div (x1 mode) 1mV/div - 1V/div (6MHz, –3dB) (x5 mode) |
Attenuator |
1-2-5 sequence, 10 step attenuator, plus vernier control |
Rise time |
About 14ns |
Over shoot |
Less than 5% |
Input impedance |
1MOhms +/-2%, 25pF +/-10pF |
Max. input voltage |
400V (DC + AC peak) |
Operating modes |
CH 1, CH 2, DUAL (ALT or CHOP) and ADD |
Chop frequency |
Approximately 500kHz |
Algebraic addition |
CH 1 + CH 2, CH 1 - CH 2 |
Inverter |
CH 2 only |
Horizontal Amplifier |
X-Y mode |
Switch selectable using X-Y switch
CH 1 X-axis
CH 2 Y-axis |
Accuracy |
Y-axis +3%. X-axis +6% |
Bandwidth |
DC - 1MHz (–3dB) |
X-Y phase difference |
Approximately 3O at 50kHz |
Sweep System |
Sweep display mode |
Main, Mix, Delay (S-1330 only) |
Hold off time |
5:1 continuously variable |
Main Sweep |
Sweep speed |
0.1µs/div - 0.2s/div in 1-2-5 sequence, 20 steps |
Accuracy |
+/-3% |
Variable time control |
5:1, uncalibrated, continuously variable between steps |
Sweep magnification |
10X, +/-10%, extend sweep speed up to 10ns/div |
Delayed Sweep (S-1330 only) |
Sweep speed |
0.1µs/div - 0.2s/div in 1-2-5 seq., 20 steps |
Accuracy |
+/-3% |
Sweep magnification |
10X, +/-10%, extend sweep speed up to 10ns/div |
Delay time position |
Variable control to locate desirable waveform for extending |
Trigger |
Trigger coupling |
AUTO, NORM, TV-V, TV-H |
Trigger source |
CH 1, CH 2, LINE, EXT |
Slope |
+/- |
Trigger Sensitivity |
Coupling |
Bandwidth |
Internal |
External |
TV-V |
20Hz - 1kHz |
0.5 div |
0.05Vpp |
TV-H |
1kHz - 100kHz |
0.5 div |
0.05Vpp |
AUTO |
100Hz-30MHz |
1.5 div |
0.1Vpp |
NORM |
100Hz-30MHz |
1.5 div |
0.1Vpp |
|
Component Tester (S-1330 only) |
Test voltage |
Max. 6Vrms (open circuit) |
Test current |
Max. 11mA (shorted) |
Test frequency |
Line frequency |
Components |
Capacitor, inductor, diode, transistor, zener, etc |
Other Specifications |
CRT Type |
Rectangular with internal graticule. Adjustable graticule illumination (S-1330 only) |
CRT Display area |
8 x 10 div (1 div = 1 cm) |
CRT Accelerating voltage |
2.1kV |
CRT Phosphor |
P31 |
Z modulation (S-1330 only) |
Positive TTL signal, low level blank intensity at any intensity, high level unblank any intensity |
Trace rotation |
Adjustable front panel |
Calibrator |
Square wave 1kHz, 2Vpp +3% |
Power requirements |
115, 230VAC +10%, 50/60Hz |
Power consumption |
Approximately 40 watts |
Dimensions |
5 1/4” (H) x 12 3/4” (W) x 15 5/8” (D) |
Net weight |
16 lbs. 12 oz. (7.6kgs.) |
Accessories supplied |
Two x1, x10 probes, schematic diagram & parts list, AC power cord, spare fuse, and dust cover |