| General Specifications |
| Sensing type |
Convergent reflective |
Diffuse reflective |
Through-beam |
| Sensing distance |
10 to 30mm *3 |
10 to 50mm *3 |
100mm *3 |
3m |
| Sensing target |
Translucent, opaque materials |
Opaque materials of Min. ø6mm |
| Hysteresis |
Max. 10% at sensing distance |
Max. 25% at sensing distance |
- |
| Response time |
Operation: Max. 3ms, Return:Max. 100ms (When the time adjustment VR is minimum) |
Operation:Max. 3ms Return:Max. 100ms |
Max. 1ms |
| Power supply |
12-24VDC ±10%(Ripple P-P : Max. 10%) |
| Current consumption |
Max. 35mA |
Max. 30mA |
| Light source |
Infrared LED |
| Sensitivity adjustment |
Fixed |
Built-in the adjustment VR |
Fixed |
| Operation mode |
Light ON |
Dark ON(Light ON : Option) |
| Control output |
NPN open collector output
•Load voltage : Max. 30VDC
•Load current : Max. 50mA
•Residual voltage : Max. 1V |
NPN or PNP open collector output
•Load voltage :Max. 30VDC,
•Load current : Max. 100mA,
•Residual voltage - NPN: Max.1V, PNP: Max. 2.5V |
| Protection circuit |
Reverse polarity protection, output short-circuit protection |
| Timer function |
Built-in(OFF delay) delay Time : Max. 0.1 to 2 sec.(adjustment VR) |
- |
| Indication |
Operation indicator : red LED |
| Insulation resistance |
Min. 20MΩ(at 500VDC megger) |
| Noise resistance |
±240V the square wave noise(pulse width : 1μs) by the noise simulator |
| Dielectric strength |
1,000VAC 50/60Hz for 1minute |
| Vibration |
1.5mm amplitude or 300m/s2 at frequency of 10 to 55Hz(for 1 min.) in each of X, Y, Z directions for 2 hours |
| Shock |
500m/s2(approx. 50G) in each of X, Y, Z directions for 3 times |
| Environment |
Ambient illumination |
Sunlight: Max. 11,000lx, Incandescent lamp: Max. 3,000lx(Receiver illumination) |
| Ambient temperature |
-20 to 65°C, storage : -25 to 70°C |
| Ambient humidity |
35 to 85%RH, storage : 35 to 85%RH |
| Protection |
Standard type: IP64(IEC standards) /
*1,*2: IP50(IEC standards) |
IP50(IEC standard) |
IP64(IEC standard) |
| Material |
Case: ABS, Sensing part: Acrylic |
| Cable |
ø3.5, 3-wire, Length: 2m(Emitter of through-beam type: ø3.5, 2-wire, Length: 2m) (AWG24, Core diameter: 0.08mm, Number of cores: 40, Insulator out diameter: ø1) |
| Accessory |
VR adjustment driver, Mounting bracket A, M3 Screws, Nuts |
Mounting bracket A, M3 Screws, Nuts |
| Approval |
CE |
| Unit weight |
Approx. 70g |
Approx. 150g |
*1: Operation indicator is on the top.
*2: OFF delay timer is built-in. (Delay time : Max. 0.1 to 2sec.)
*3: Sensing distance for Non-glossy white paper(50×50mm)
*The temperature or humidity mentioned in Environment indicates a non freezing or condensation environment. |