Autonics BEN Series General Specifications
(Free power, Relay contact output type) |
Sensing type |
Through-beam |
Retroreflective
(Standard type) |
Retroreflective
(Built-in polarizing filter |
Diffuse reflectiv |
Sensing distance |
10m |
0.1 to 5m*1 |
0.1 to 3m*1 |
300mm*2 |
Sensing target |
Opaque materials of Min. ø16mm |
Opaque materials of Min. ø60mm |
Translucent, Opaque materials |
Hysteresis |
- |
Max. 20% at ratedsetting distance |
Response time |
Max. 20ms |
Response time |
24-240VAC ±10% 50/60Hz, 24-240VDC ±10%(Ripple P-P : Max. 10%) |
Power consumption |
Max. 4VA |
Light source |
Infrared LED(850nm) |
Red LED(660nm) |
Infrared LED(940nm) |
Sensitivity adjustment |
- |
Adjustment VR |
Operation mode |
Selectable Light ON or Dark ON by VR |
Control output |
Relay contact output
- Relay contact capacity: 30VDC 3A of resistive load, 250VAC 3A resistive load
- Relay contact composition: 1c
|
Relay lifetime |
Mechanically: Min. 50,000,000 operation, Electrically: Min. 100,000 operation |
Light receiving element |
Photo IC |
Indicator |
Operation indicator : red
Stability indicator : green
(The red lamp on Emitter of transmitted beam type is for power indication) |
Insulation resistance |
Min. 20MΩ(at 500VDC megger) |
Insulation type |
Double or strong insulation (Mark : Dielectric voltage between the measured input and the power: 1kV) |
Noise resistance |
±1,000V the square wave noise(pulse width : 1μs) by the noise simulator |
Dielectric strength |
1000VAC 50/60Hz for 1minute |
Vibration |
Mechanical |
1.5mm amplitude or 300m/s2 at frequency of 10 to 55Hz(for 1 min.) in each of X, Y, Z directions for 2 hours |
Malfunction |
1.5mm amplitude or 300m/s2 at frequency of 10 to 55Hz(for 1 min.) in each of X, Y, Z directions for 10 minutes |
Shock |
Mechanical |
500m/s2(approx. 50G) in each of X, Y, Z directions for 3 times |
Malfunction |
100m/s2(approx. 10G) in each of X, Y, Z directions for 3 times |
Environment |
Ambient illumination |
Sunlight : Max. 11,000lx, Incandescent lamp : Max. 3,000lx(Receiver illumination) |
Ambient temperature |
-20 to 65°C, storage : -25 to 70°C |
Ambient humidity |
35 to 85%RH, storage : 35 to 85%RH |
Protection |
IP50(IEC standard) |
Material |
•Case, Case cover: Heat resistant ABS
•Sensing part: PC(with polarizing filter: PMMA) |
Cable |
ø5, 5-wire, Length: 2m(Emitter of through-beam type: ø5, 2-wire, Length: 2m) (AWG22, Core diameter: 0.08mm, Number of cores: 60, Insulator out diameter: ø1.25) |
Accessory |
Individual |
- |
Reflector(MS-2) |
- |
Common |
VR adjustment driver, Mounting bracket, Bolts/nuts |
Unit weight |
Approx. 354g |
Approx. 208g |
Approx. 195g |
*1: The sensing distance is specified with using the MS-2 reflector and same as the MS-4 reflector. Sensing distance is setting range of the reflector. The sensor can detect under 0.1m.
*2: It is for Non-glossy white paper(100×100mm).
*The temperature or humidity mentioned in Environment indicates a non freezing or condensation environment. |