Shimpo Accessories

• AC Adapters / Chargers	• Hook
• Cable	• Test Stand Plate
• Grip	• Miscellaneous
• Handle

AC Adapters / Chargers [ Back to Top ]
Images	Model Number	Description
	CONE	Cone Adapter 1/2 inch
	FUNNEL	Funnel Adapter 0.5 Inch
	FG-09V120UC	Ac Adapters / Chargers - FG-09V120UC (Standard-universal 110/220 volt adapter/charger)
	FG-M4ADP	FGE-X/FGV-X/FGV-XY/DFS Adapter Set
	FG-M6ADP	Steel FGE-X/FGV-X/FGV-XY/DFS adapter set, 110 lbs. capacity
	FG-M10ADP	FGE-HX/FGV-HX adapter set

Cable [ Back to Top ]
Images	Model Number	Description
	DFS-Analog	Facilitates an analog output for recording purposes (amplitude of signal is ± 1 VDC).
	DFS-Digimatic	Allows data transfer to a Mitutoyo data collector.
	DFS-RS232	Permits communication between force gage and a PC.
	FGS-Analog	Force Gauge Analog Output Cable
	FGS250PV-RS232	Interface Cable FGS-250PV Flex Test Stand to RS232
	FGV-Analog	FGV Force Gauge Analog Output Cable
	FGV-RS232	Interface Cable FGV Force Gauge to PC RS232
	FGS-50PCABLE	DFS to FGS-100PV: replaces DFS-CTRL-DELUXE w/FGV-RS232
	DFS-CTRLCABLE	Load-cell protection for DFS with FGS-100PV series test stand
	FGV-CTRLCABLE	Load-cell protection with FGV and motorized test stand
	FG-M4TJ10	Metric 4 female to 10/32 male
	FG-M4TM6	Metric 4 female to metric 6 male
	FG-M6TJ10	Metric 6 female to 10/32 male
	FG-10TJM6	10/32 female to metric 6 male
	FG-M6TM10	Metric 6 female to metric 10 male
	FG-M10TJ5/16	Metric 10 female to 5/16 male
	FG-M10TM6	Metric 10 female to metric 6 male

Grip [ Back to Top ]
Images	Model Number	Description
	FG-FAB80B	Fabric Grip 500 lb Capacity M10 Thread, Mounts to Test Stand, Sold Individually
	FG-M10CLV10U	Odd shaped parts, punched samples or tension springs are easily secured and tested. Concave shape to pins assures centering under load. Throat clearance with pin is 0.5" (12.7 mm) and can easily accept samples up to 0.375" (9.65 mm) wide.
	FG-M10TEN7U	Manually tightened jaw faces can accept samples 1.25" (31.75 mm) wide and 0.25" (6.35 mm) thick. Contact faces are serrated hardened tool steel.
	FG-M10TWN500U	A unique figure 8 wrap of specimen assures a center break and non-locking pins permit quick installation and release. Throat and pin clearance is 0.375" (9.65 mm) wide with the throat width being 0.5" (12.7 mm).
	FG-M10WDG500U	Wedge Grip 500 lb Capacity M10 Thread, Sold Individually. Spring loaded jaws automatically close on the specimen and tighten as tension applied. Ideal for testing wires, strip material and plastic tape or films.
	FG-M6FLM20	These heavy-duty, spring-loaded grips have serrated jaws for handling samples up to 0.39" (10 mm) thick and 0.79" (20 mm) wide.
	FG-M6FLM50U	These heavy-duty, spring-loaded grips have serrated jaws for handling samples up to 0.39" (10 mm) thick and 1.97" (50 mm) wide.
	FG-M6FPG3	Perfect for testing fine and medium gage wire, ribbon, tape and paper. Two jaw widths and load capacities are available; both can handle material thickness up to 0.04" (1 mm), Jaw widths are 0.12" (3 mm).
	FG-M6FPG8	Perfect for testing fine and medium gage wire, ribbon, tape and paper. Two jaw widths and load capacities are available; both can handle material thickness up to 0.04" (1 mm), Jaw widths are 0.31" (8 mm).
	FG-M6FTG20U	Each serrated gripping face is 0.79" (20 mm) square and can accept samples up to 0.79" (20 mm) thick.
	FG-M6JAC5U	Designed for testing low gage wire and rigid rods; accepts material diameters from 0.02" (0.05 mm) to 0.20" (5 mm).
	FG-M6PIN05	Ideal for gripping fine wires and filaments. For checking samples of 0.5 mm thick.
	FG-M6PIN1	Ideal for gripping fine wires and filaments. For checking samples of 1 mm thick.
	FG-M6PIN2	Ideal for gripping fine wires and filaments. For checking samples of 2 mm thick.
	FG-M6SPO10U	Ideal for hard-to-hold items like thread, filaments, etc. The sample is wrapped around the spool, anchored by friction.
	FG-M6TAP30U	Self-tightening lever action makes this fixture perfect for testing rubber, tape and paper.
	FG-M6WDG50U	Two capacities for lighter and heavier loads; Ideal for testing wires, strip material and plastic tape or films.
	FG-TEN7B	Manually tightened jaw faces can accept samples 1.25" (31.75 mm) wide and .25" (6.35 mm) thick. Contact faces are serrated hardened tool steel.
	FG-TWN500B	A unique figure 8 wrap of specimen assures a center break and non-locking pins permit quick installation and release. Throat and pin clearance is 0.375" (9.65 mm) wide with the throat width being 0.5" (12.7 mm).
	FG-M4PIN05	0.5mm maximum pin grip
	FG-M4PIN1	1 mm maximum pin grip
	FG-M4PIN2	2 mm maximum pin grip
	FG-M4FPG3	3 mm wide fine point grip
	FG-M4FPG8	8 mm wide fine point grip
	FG-M4FLM20	20 mm wide film grip
	FG-M10FAB80U	Fabric grip
	FG-M6COMP100U	100 mm compression plate
	FG-FLM50B	50 mm wide film grip
	FG-JAC5B	Jacobs chuck grip
	FG-FTG20B	Flat chuck tensile grip, 100 lbs. capacity
	FG-SPO10B	Spool grip
	FG-TAP30B	Tape grip
	FG-WDG50B	Wedge grip
	FG-CLV10B	Clevis grip
	FG-HORIZ-ADAP	Mounting block for attachments and grips for use with FGS-100PXL and FGS-100PXH Horizontal test stands

Handle [ Back to Top ]
Images	Model Number	Description
	FG-Handle	This handle is recommended if manually pulling or pushing more than 30 lbs. The handle easily attaches to the back of the FGE and FGV series gauges.
	FGH-HANDLE	Handle for FGE-H/FGV-H Digital Force Gauges
	MFP-HANDLE	Handle for MF Series Mechanical Gauges

Hook [ Back to Top ]
Images	Model Number	Description
	FG-M6FKL-AL	Aluminum fork hook, 20 lbs. capacity
	FG-M6HKL-AL	Aluminum large hook, 20 lbs. capacity
	FG-M6ADP-AL	Aluminum adapter set, 20 lbs. capacity
	FG-M6FKL	(Fork hook) Fork Hook
	FG-M6HKL	(Large hook) Large Hook

Test Stand Plate [ Back to Top ]
Images	Model Number	Description
	FG-M10ADHE3	Shimpo Adhesive Test Plate Set (Upper and Lower) 500 lb Capacity M10 Thread, Accepts Samples to 76.20 mm, Ball Socket Mounting.
	FG-M10COMP100U	Compression Plate 100 mm Diameter, M10 Thread, Sold Individually
	FG-M10COMP50U	Compression Plate 50 mm Diameter, M10 Thread, Sold Individually
	FG-M6COMP50U	Compression Plate 50 mm Diameter, M6 Thread, Sold Individually
	UNI-PLATE	Test stand mounting plate for competitors gauges and MF/JAVELIN
	DFS-CTRL-BASIC	Controls FGS-50PV test stand with Hi-Lo limits on DFS
	DRI-FGS250P	Interface cable, from DRI and DFS to FGS-250PV series test stand
	FGV-FGS250P	Interface cable, from FGV to FGS-250PV series test stand
	FGV-FGS200PV-CBL	Communication cable from FGV-X/XY gauge to FGS-200PV stand
	FGS-LENGTH-L	Digital Length/Height meter for lever stands (FGS-100L and FGS-50S)
	FGS-LENGTH-H	Digital Length /Height meter for hand-wheel stands (FGS-100H)

Miscellaneous [ Back to Top ]
Images	Model Number	Description
	FG-M6WTER100	Designed specifically to test the strength of wire / terminal connections. The upper grip consists of a self-aligning wheel with nine equally spaced slots of various terminal shank sizes
	N.I.S.T.	N.I.S.T. Traceable Certificate of Calibration with Calibration Data
	EXT-SHAFT	Extention Shaft 3.5 Inch
	FPM-12	Measuring Wheel 12 Inch
	FPM-12CBL	Measuring Wheel 12 Inch for Cable/Wire
	FPM-6	Measuring Wheel 6 Inch
	TAPE	Reflective tape 1 x 7.75 Inch Strip
	TNP-TP30	Set of 4 standard replacement pegs, 30mm height
	TNP-TP50	Set of 4 standard replacement pegs, 50mm height
	FG-M6PUNCTURE-ST	Puncture fixture
	FGS-ACC	Accesory kit for FGS Test Stands
	ERGO-KIT	3-piece padded PT/ERGO accessories

Shimpo Main Page

Shimpo Price List